Complies with IEC 61557 • Designed to IP 54 Rating • Live circuit and wiring connection check LED's • Triple ranges insulation tests at 250, 500 and 1000V • Triple range loop and PSC tests 15mA test current at 200Ω/2000Ω range(No RCD Trip) • Phase angle selection on RCD ranges • Polarity switch for continuity tests • Auto-null facility for continuity tests • Earth probe for loop impedance testing on extraneous metalwork • Contact Voltage Reading • Test of a large kind of RCD's: Standard, Selective, AC and A(DC sensitive breakers)
Designed to meet IEC 61010-1 CAT.III 600V • Test leads with remote control switch.(For insulation&Simplified Earth Test) • Back light function. • Color coded scales and range switch position for easy reading. • Automatic warning when resistance of auxiliary earth spikes is in excess of tolerance. • Can be hung around the neck for both hand’s operation.
Kew Combitester provides the ultimate in Microprocessor technology offering Loop and RCD tests with a comprehensive memory and downloading test results. • LOOP Impedance 200/2000Ω range measurement is carried out using a test current of 15mA. This current will not trip RCD’s rated at 30mA or greater. • High resolution for low Loop Impedance (resolution of 0.01Ω) on 20Ω range. • Direct reading of Prospective Short Circuit Current (PSC) and earth fault current. • RCD tests at 0 and 180 degree phase angle switch permit quick tests and consistent readings. • Test of a large kind of RCD's:Standard, Selective, AC and A (DC sensitive breakers). • Constant current source circuitry ensures that a fluctuating mains voltage does not affect the accuracy of readings. • RCD Ramp test in order to indicate the actual tripping current of RCD. • Contact Voltage Reading (UC). with two selectable contact voltage limits (50 and 25V). • Visual indication of correct wiring status and automatic lock-out if test resistors overheats. • Designed to IEC 61010-1, IEC 61557 and high protection degree IP54. • The...
The KEW 6201A is a portable appliance tester, performing four functions to ensure the Safety of ClassI and ClassII appliances. And also can measure the mains voltage. Readings are displayed on a large liquid crystal display (LCD) below which are four LEDs which unambiguously display a pass or fail indication for threshold values dictated by AS/NZS 3760.
The Model 6202 is a hand-held portable appliance tester, performing four functions to ensure the Safety of Class I, Class II and Class III 230V appliances. And also can measure the mains voltage.Readings are displayed on a large liquid crystal display (LCD) below which are eight LEDs which unambiguously display a pass or fail indication for threshold values dictated by DIN VDE 0701/0702
Comprehensive real-time monitoring, recording and analysis of single and 3-phase systems • Voltage, Current, Power Factor and Frequency measurements • Power analysis (Active, Apparent and Reactive power) • Energy analysis (Active, Apparent and Reactive power) • Active power accuracy: ±0.3%rdg±0.2%f.s. • Automatic wiring check function to prevent incorrect connections • Large memory capability (2GB) using built-in SD card interface • Real time & remote measurements using Android application • synchronous measurements between two units of KEW 6305 • Wide selection of clamp sensors allow measurements from 0.1A to 3000A • The instrument automatically recognizes what kind of clamp sensor is connected to it
Simultaneous Power & Power quality measurementsPower/ Harmonics/ Waveform/ Power quality are recorded at all CHs. (Voltage: 3ch, Current 4ch) • Helpful support functionsQuick Start Guide, Wiring check and Sensor detection for easy and reliable measurement • Measurement with high accuracy Guaranteed accuracy: ±0.3%rdg (energy),±0.2%rdg (voltage/ current) Complies with the International Standard IEC 61000-4-30 Class Sand the European Standard EN50160 • Remote monitoring on PC and Android deviceRemote checking of measurement in real-time is possible via Bluetooth communication.Recorded data can be saved in the supplied SD card.EN50160 report can be generated after survey by PC software.
12 kinds of power measurements Voltage (RMS), Current (RMS), active power, apparent power, reactive power, active energy, apparent energy, reactive energy, power factor (cos θ), frequency , demand measurement, current flowing on the neutral line(Only on 3 phase 4 wire measurement) Regenerative electric power can be measured Detection of consumption power and regenerative electric power Regenerative electric power: This is the electric power which is generated by private power generator, and is supplied to electric power company. Display 3 different data simultaneously on large screen. 4 types wiring system 1 phase - 2 wire (1ch) (2ch), (3ch) 1 phase - 3 wire 3 phase - 3 wire 3 phase - 4 wire